67 Designs RH4x4 Roll Bar Mount, TrailDash2 Mount, Elbow Connector, and a Mini Arm

[youtube https://www.youtube.com/watch?v=J1tJt9S-6Vs&w=640&h=360]

Finally got some stuff I have been waiting for for a while... so this is a quick video to show you what it is! So glad I have a way to easily mount my Superchips TrailDash 2 (TD2) to my Rock Hard 4x4 Sport Cage. The guys over at 67d.com really came through on this... and it's perfect!

09 - Alarm and Remote Start 2-Way Controller Overview - What to Press - What it Does - Excalibur

[youtube https://www.youtube.com/watch?v=aZBKdFCTbvs&w=640&h=360]

In this video I go over the 2-way controller for the Omega Excalibur AL-1775-3DB. What button combinations do what functions. What the vehicle does in response, and also what alerting and notifications the controller gives you.

08 - Alarm and Remote Start - User Programmable Features - Excalibur

[youtube https://www.youtube.com/watch?v=9O7a26V6_-s&w=640&h=360]

In this video, I go over setting the various User Programmable Features in the Omega Excalibur AL-1775-3DB Alarm and Remote Start System.

Feature #1 - Remote Start Run Time
Feature #2 - Flashing Light Confirmations
Feature #3 - Confirmation Chirp Volume
Feature #4 - BROWN Wire Audible Output
Feature #5 - Ignition Controlled Lock/Unlock
Feature #6 - Open Door Bypass of Ignition Locking
Feature #7 - Unlock w/ Trunk Release
Feature #8 - Remote Start Activation From The Remote
Feature #9 - Last Door Arming
Feature #10 - Automatic Rearming
Feature #11 - Confirmation Chirps
Feature #12 - Anti-Carjacking
Feature #13 - SecureCode
Feature #14 - Ignition Activated Override
Feature #15 - Alarm Trigger Duration
Feature #16 - Arming Delay
Feature #17 - Open Door Warning Upon Arming

Here's how to enter programming mode:

Step 1 Turn the ignition key “ON”, then “OFF”.
(I found waiting a couple of seconds helped)

Step 2 Within 5 seconds of step 1, press the valet switch 5 times to access user features
~ The siren/horn will sound and the status light will turn on.

Step 3 Within 10 seconds of step 2, press the valet switch the number of times corresponding with the desired feature’s number.
~ The siren/horn will chirp, the status light, and the parking lights will flash equal to the selected feature.

Step 4 Change the feature by pressing the transmitter button that corresponds with the desired setting. The siren/horn will chirp to correspond with the chosen setting.

IT'S EASY!!! How To Program Transponder Keys for Late Model Jeep Wrangler

[youtube https://www.youtube.com/watch?v=SiMNugU45mY&w=640&h=360]

In this video I show you how easy (and HARD) it is to add a new key for your late model Jeep. This process is likely similar for a variety of videos... so check out the link I share in the video for detailed instructions for whatever vehicle you have. These are the keys I am adding: http://amzn.to/2yroqbV. You can also get versions of these keys with the transceiver (buttons) and the programming steps are the same.

I added these keys because since I installed the Omega Excalibur alarm system, I no longer need the large factory Jeep key. This allows me to save some bulk and weight in my pocket.

[REPOST] AOAA Wheeling Trip - 10-7-17 - OVERCLOCK3D, a built TJ, and a Stock TJ - Seicane Footage

[youtube https://www.youtube.com/watch?v=i7izTbrMDek&w=640&h=360]

[Sorry had to repost thanks to a Drake song playing in the background of one of the scenes that caused my video to be blocked in ALL COUNTRIES! lol]

A couple of us from the office got together out at Anthracite Outdoor Adventure Area in Northumberland County, Pennsylvania for some easy going wheeling. We had a new Jeeper with us who was wanting to take his stock new-to-him TJ out before he started installing his lift kit.

I hope you enjoy the video.

Oh... here is the link to the Seicane stereo...since I always get so many questions about that. Seicane Model S18JP25 — http://bit.ly/S18JP25

For more info about the Stereo and a ton of install videos, see my Seicane playlist:

https://www.youtube.com/playlist?list=PLKivmulOhtZgXRmaZjF2hJuGVfHfRhjFW


Some helpful O3D Jeeps links for you:
Most Recent Upload : https://goo.gl/z2AFkB
Most Popular Upload : https://goo.gl/y6bCWo
Check out my Channel : https://goo.gl/t8crvN

07 - Alarm and Remote Start Install - Buttoning it up, Blade Programming, Vehicle Learn Mode - OMEGA

[youtube https://www.youtube.com/watch?v=2Rt4xeXLOt8&w=640&h=360]

============ CHECK THIS OUT! =========
Get the OVERCLOCK3D AL-1775-3DB PACKAGE FOR 2007+ WRANGLERS over at http://kickyride.com/index.php?main_page=product_info&cPath=1_4&products_id=168

USE DISCOUNT CODE "O3DJEEPS" TO SAVE 10% ON YOUR ORDER! (Discount code value through 12-01-2017.)
=====================================

In this video, I plug everything into the brain (except for the final two optional sensors I'll add later) and tuck it away in it's new home. I show you how to program the blade to recognize and operate with your specific vehicle, and I show you how to use Vehicle Learn to handle a bunch of programming steps... automatically!

Here's the playlist containing all of the videos for this install:
https://www.youtube.com/playlist?list=PLKivmulOhtZjzT8-D_3LBg5ex3ldvoFOS

Here's the OMEGA Excalibur Video on Vehicle Learn:
https://www.youtube.com/watch?v=Hi1rEJjuGF0

Vehicle Learn is a patent pending technology introduced with the new Excalibur 70 series remote start line. It's one of several time saving installation technologies developed for the 70 series. In less time than programming one feature manually, you can accomplish the following:

- Set engine type
- Automatically recognize the ignition switch sequence and configure all primary outputs to match
- Confirm how many circuits were detected and that connections are good
- Automatically detect and select proper data port protocols
- Automatically detect and select the best available engine detection method
- Enable manual transmission reservation mode
- and a few more tricks up our sleeves...

PLEASE READ - IMPORTANT INFO!

So you want to install an alarm system and remote start into your Jeep Wrangler? Well… this is the page for you! What follows below is the complete video series regarding the selection, overview, installation, setup, and howtos of the Omega Excalibur AL-1775-3DB security system and remote start I installed in my 2015 Jeep Wrangler with automatic transmission. If you happen to have the same vehicle (including similar years) then this page should be a step-by-step guide for you. If you have a manual transmission, there will be some additional steps and wiring for you, and what exactly depends on what year your Jeep is. I tried to mention some of those things throughout the video series. If you have a 2017 or newer, also note that the access to the ignition switch harness is a little different. I’ll also try and help you out there.

Please watch all of the videos BEFORE YOU START your own installation. This is important because I may point out things in later videos that would be helpful to know about early on. It’s just part of the process. Once I get into the install, I know more about what exactly needs to be done, versus what I believe needs to be done. A great example of this is the wiring for the parking lights. In the wiring prep video, I told you that you needed three wires for this because that was the industry standard based on how the Jeeps were wired. However, in actual testing during the install (and working closely with the tech guys at Omega Research and Development) I found that only one wire was really needed. So I modified the harness from the original 9 wires, down to 7!! BONUS!!!

06 - Alarm and Remote Start Install - OBDII, Ground, Parking Lights, Horn, Siren, Hood Pin Switch

[youtube https://www.youtube.com/watch?v=zFFBY-4-JbE&w=640&h=360]

============ CHECK THIS OUT! =========
Get the OVERCLOCK3D AL-1775-3DB PACKAGE FOR 2007+ WRANGLERS over at http://kickyride.com/index.php?main_page=product_info&cPath=1_4&products_id=168

USE DISCOUNT CODE "O3DJEEPS" TO SAVE 10% ON YOUR ORDER! (Discount code value through 12-01-2017.)
=====================================

In this video we complete all of the wiring for the basic system. I still have a proximity sensor and hood tilt sensor to wire in, but I'll do that later. The final wiring demonstrated in this video is the two power connections to the OBD-II port, the ground connection, the parking lights tap, and wiring in the horn, hood pin switch, and the siren. The only thing left to do after this is basically plug in the brain of the Omega Excalibur 1775 and run through a couple of easy self-programming steps for the system and the remote start capability. We're so close to being done!!! Next video gets you operational, I promise!!!!

Here's the playlist containing all of the videos for this install:
https://www.youtube.com/playlist?list=PLKivmulOhtZjzT8-D_3LBg5ex3ldvoFOS

PLEASE READ - IMPORTANT INFO!

So you want to install an alarm system and remote start into your Jeep Wrangler? Well… this is the page for you! What follows below is the complete video series regarding the selection, overview, installation, setup, and howtos of the Omega Excalibur AL-1775-3DB security system and remote start I installed in my 2015 Jeep Wrangler with automatic transmission. If you happen to have the same vehicle (including similar years) then this page should be a step-by-step guide for you. If you have a manual transmission, there will be some additional steps and wiring for you, and what exactly depends on what year your Jeep is. I tried to mention some of those things throughout the video series. If you have a 2017 or newer, also note that the access to the ignition switch harness is a little different. I’ll also try and help you out there.

Please watch all of the videos BEFORE YOU START your own installation. This is important because I may point out things in later videos that would be helpful to know about early on. It’s just part of the process. Once I get into the install, I know more about what exactly needs to be done, versus what I believe needs to be done. A great example of this is the wiring for the parking lights. In the wiring prep video, I told you that you needed three wires for this because that was the industry standard based on how the Jeeps were wired. However, in actual testing during the install (and working closely with the tech guys at Omega Research and Development) I found that only one wire was really needed. So I modified the harness from the original 9 wires, down to 7!! BONUS!!!