Saturday, August 25, 2018

Rock Hard 4X4 Transmission Crossmember - RH-9061 - Install & Factory Removal 2015 Jeep Wrangler JK

[youtube https://www.youtube.com/watch?v=YiLd8rEcUts&w=640&h=360]

I finally got around to replacing the beat up factory transmission crossmember on OVERCLOCK3D. I wanted to do this before putting on the other skid plates... so as you can guess... those are coming soon!

🔔 Please SUBSCRIBE if you want to see my videos! 🔔

From: https://www.rockhard4x4.com/product_p/rh-9061.htm

ROCK HARD 4X4™ DOUBLEWALL TRANSMISSION CROSSMEMBER FOR 3.6L JEEP WRANGLER JK 2/4DR 2012 - 2018 [RH-9061]

Rock Hard 4x4 is very proud to offer the Heaviest Duty Transmission Crossmember for the Jeep Wrangler JK 2/4DR 2012 - 2018 3.6L.

Upgrade your factory 14-gauge stamped steel transmission crossmember to our 3/16" + 3/16" MASSIVE 3/8" DoubleWall Crossmember!

Total Weight: 27 lbs.

Our top and bottom plate 3/16" thick design gives you a total of 3/8" plate steel strength! Designed to fit 2012-2018 3.6L engines.

Ease of Install
In under 1 hour - including removal of your factory crossmember - you can complete this critical upgrade. We designed this crossmember to be a drop in replacement for your factory transmission crossmember. Simple hand tools required - no drill cutting or welding!

Precision Made Strength
Each crossmember is laser cut from 3/16" thick steel and coated in our weather and debris resistant powder coat finish. Strength is proven on virtually all Jeep enthusiast forums with glowing reviews. Since 2007 our skid plate system has been the undisputed leader in undercarriage protection.

Components
RH4x4 crossmembers are very recognizable for two major reasons: beefy unmatched strength and laser precision fitment. What makes up a RH4x4 crossmember is what makes it so strong.

Powder Coated Finish
Other crossmembers on the market come bare steel adding an unexpected and unfortunate setback. Ours comes ready to install right out of the box.

30 comments:

  1. I run the RH oil pan and TC skid. I didn't swap out the crossmember because I felt like the two skids strengthened the stock crossmember enough for my needs. And after watching your video thats way more effort than I would be willing to put into a new cross member.

    ReplyDelete
  2. I run the RH oil pan and TC skid. I didn't swap out the crossmember because I felt like the two skids strengthened the stock crossmember enough for my needs. And after watching your vide thats way more effort than I would be willing to put into a new cross member.

    ReplyDelete
  3. o3djeeps [ OVERCLOCK3D Jeeps ]August 25, 2018 at 5:15 PM

    If mine wasn't beat up or I had already installed the skid plates I agree 100% but since I had the opportunity to do it now I figured I may as well. It is supposed to be a direct replacement, but having to deal with using the straps did add a little time to it. It was easy... But not "simple".

    ReplyDelete
  4. Stop making me want to buy things that i didn't know I needed! lol

    ReplyDelete
  5. Is this for Auto and Manual?

    ReplyDelete
  6. Nice video... From what I’ve heard It sounds like Jeep put the crossmember on the bottom of the frame on the JL instead tucked inside like on the JK.. I sometimes wonder if waiting for the JL diesel is worth it or should I go the JK route.. Ha Ha..

    ReplyDelete
  7. Hey Chris, trailrecon is out in moab now..have you talked to him or been watching his videos about it? He didnt go through hells gate because of his tent on top( why he didnt just take it off after he drove all the way out there is beyond me) are you going through the gate? Interested to see the mpg for your trip also. Enjoy/be safe.

    ReplyDelete
  8. Is there anything else that poor 3.6 needs to haul around

    ReplyDelete
  9. The extra weight can give you a lower center of gravity ? More stability with the lower weight

    ReplyDelete
  10. lol.... when i saw you tapping on that thing with a deadblow hammer... I immediately thought "block of wood and BFH"... aaannnd there it is. hahaaaa. Not sure how it would be with your LA system, but usually a couple of good raps on the mounting tabs to spread them slightly fixes most of that.

    ReplyDelete
  11. That install looked like a pain in the butt. A new cross member is on my to do list. Thanks for the video.

    ReplyDelete
  12. What model Dewalt impact are you using? I have been looking at some of the smaller ones but not sure iof they would be strong enough.

    ReplyDelete
  13. Chris Cpo Poldervaart Ive been using rust converter on any rock scratches on my control arms, gas tank skid, etc. after everytime I go wheeling. But, I see you’ve got a bunch of rusty scratches on your underside, should I be less worried about it and just let it go?

    ReplyDelete
  14. Another one getting added to my wishlist list !!! Thanks for sharing, my wife is not liking how long the list is.

    ReplyDelete
  15. Timely video. I was installing new skid plates today and realized to do it correctly I should replace the crossmember. I already have skids that bolt into the bolt holes for the factory skid, does the RH crossmember have the bolt holes for the factory skid in the OEM location? Thx

    ReplyDelete
  16. o3djeeps [ OVERCLOCK3D Jeeps ]August 26, 2018 at 6:35 PM

    Yep... It's exactly the same as the stock one.

    ReplyDelete
  17. o3djeeps [ OVERCLOCK3D Jeeps ]August 26, 2018 at 6:37 PM

    +Howard Morris as far as I am aware
    .. it's the same cross member for either.

    ReplyDelete
  18. o3djeeps [ OVERCLOCK3D Jeeps ]August 26, 2018 at 6:37 PM

    I haven't talked to him, but am (and will be) watching the vids! I'm pretty sure the gate is on the list.

    ReplyDelete
  19. o3djeeps [ OVERCLOCK3D Jeeps ]August 26, 2018 at 6:38 PM

    That's actually a good point

    ReplyDelete
  20. o3djeeps [ OVERCLOCK3D Jeeps ]August 26, 2018 at 6:39 PM

    Not positive but I love it. It's the 1/2 inch brushless.

    ReplyDelete
  21. Non Jeep question haha is your first name “Ceepio”?

    ReplyDelete
  22. Another great video, love my RockHard 4x4 products.

    ReplyDelete
  23. Hey Chris, looks like that one took a little more grunt than usual. I'm curious if they were dimensionaly identical? I am assuming it is powder coated rather than painted? may be just slightly wider than the stock cross member due to the coating. Then again the mounting flanges may have been compressed at the bolt holes from the torque on the bolts from the factory. I haven't had the opportunity to bounce the underside of mine off anything hard enough to beat it up YET.

    ReplyDelete
  24. Yeah I also was curious as too CPO

    ReplyDelete
  25. You can't take too much care of that stuff... I just suck at it. Lol. I will be running over the undercarriage in similar fashion... But replacing stuff helps. Hahaha

    ReplyDelete
  26. Way better for sure

    ReplyDelete
  27. o3djeeps [ OVERCLOCK3D Jeeps ]August 28, 2018 at 6:30 PM

    It is powder coated. I had to pry the original one out... So not surprised I had to work to get the new one in. As a structural cross member, I'm okay of it's a tight fit! 😁

    ReplyDelete
  28. o3djeeps [ OVERCLOCK3D Jeeps ]August 28, 2018 at 6:31 PM

    CPO is a long time nickname....

    ReplyDelete
  29. Thanks again for another informative video.

    ReplyDelete